Product Description
Good Price 4WD Small LuGong farm tractors Hay Rake Walk Behind tractor LT704-1
Lugong LT704-1 wheel tractor is a new type of tractor developed and designed by our company. The shuttle shift system is used to provide users with more choices and better meet the user's various agronomic requirements.
1.LT series of multifunctional tractors, its power cover 50-100 horsepower. Optional Rotary Tiller, Lawn Mower, Baler, Sprayer, etc farm implements.
2. It adopts 8+2 shift,reasonable speed matching, high working efficiency.
3. Dry brake is the standard configuration, and oil bath type wet brake is optional which has great breaking force and long service life.
4. Equipped with famous and high-quality engines, large torque reserve and strong power.Power emission upgrade, more advanced performance, low fuel consumption and high reliability.
5. Farmland tires, grassland tires and engineering tires are optional to satisfy various operations.
6.Four driving standard configuration mid steering cylinder front drive axle has the maximum gap from the ground of 335mm.
7.Suspension seat is the standard configuration which can effectively reduce 40% of vibration.
8. The famous brand front drive axle is highly reliable.The transmission system adopts strong gears, which is more durable.Reinforced half shaft, casing, trailer and other configurations
9. Adopting a new type of high pressure lifter makes the work more convenient and flexible.Equipped with external double oil cylinders , the working effect is better.
10.The power output speed can be selected from various speeds such as 540/720 rpm, and can be matched with a variety of agricultural machinery and tools, and the scope of application is wider.
Tractor Main Features and Advantages:
1. Equipped famous brand engine showing advanced capacity, low fuel consumption and high economic efficiency.
2. Streamlined appearance design, beautiful and generous.
3. Transmission Case adopt meshed shift and add the gearbox interlock device makes the operation more smoothly, reliable and easier.
4. Double action clutch with disc spring, perform steadily and easy to operate.
5. Fully hydraulic steering system greatly reduced driver's work strength.
6. Wet disc brake device, reliable brake performance.
7. Separate injection of hydraulic oil, reliable to operate.
Product Parameters
| LT504-1 | LT604-1 | LT704-1 | LT804-1 | LT904-1 | LT1004-1 | |
| Engine | yunnei | yunnei | yunnei | yunnei | yunnei | yunnei |
| Power | 50HP | 60HP | 70HP | 80HP | 90HP | 100HP |
| Minimum quality of use | 1800kg | 1850kg | 2571kg | 2600kg | 2850kg | 3300kg |
| Wheel base | 1970mm | 1970mm | 1970mm | 2090mm | 2090mm | 2090mm |
| overall dimension | 3595×1500×2330mm | 3685×1505×2325mm | 3690×1500×2335mm | 4190×1790×2690mm | 4190×1780×2680mm | 4190×1790×2690mm |
|
Model |
LT504-1, Wheel type |
||
|
Driving type |
4WD |
||
|
Power |
70HP |
||
|
Steering system type |
Full hydraulic steering |
||
|
Standard speed of power output shaft |
540/720r/min | ||
| Number of gears (forward/backward) | 8/2 | ||
| Engine | Laidong or HangZhouhong | ||
| External dimension (L × W × H) | 3690×1500×2335mm | ||
| Number of hydraulic output groups | 1 | ||
| Type of suspension | Three-point rear suspension | ||
Other products
What We Offer:
1. Products of Mini Excavators from 0.8 ton to 2.0 ton,mini wheel loader , backhoe excavators,wheel tractor, etc.
2. Service of pre-sale, middle-sale and after-sale all-around service.
3. Traning of machine operation, daily maintenance.
4. Technical support for any trouble shooting with our machines.
5. OEM/ODM service for wholesalers/trading companies/distributors/local agents.
Company Profile
ZheJiang LuGong Machinery Co., Ltd was founded in March 2000 which located at the junction of 3 cities(HangZhou, HangZhou and HangZhou)-HangZhou HangZhou industrial trade park and it's the backbone enterprise of construction machinery national wide with fixed asset 500million Yuan. It covers a land of 200 thousand square meters and has 1,100 employees, 88 of whom are engineers and technicians.
Our company mainly produces loaders, excavators, tippers, tricycles etc. Products are mainly sold to over 20 provinces in China and exported to dozens of countries and regions in Africa, Southeast Asia, South America and Russia. The quality and performance of our small farm-use loaders and construction tippers are in leading position of the industry throughout the nation and well received by users. Now, "Lu Gong" brand loaders and tipper have gained acceptance by dealers and uses all over China.
We focus on quality, performance and consider of users as always. In management, we've achieved a new level by adopting ISO9001:2015 international quality management system.
We would like to develop in economic construction by holding our old and new friends and users hands by following our business philosophy of "Driven by science and technology, seeking survival by quality, benefiting by managing and winning market by service" and spirit of "Pioneering, innovating and pursuing excellence".
Packaging & Shipping
FAQ
Q: Why should I choose LuGong instead of other brands?
A: With 22 years exporting experience, LuGong has been a well known brand in the market, now you can see LuGong machines working in more than 40 countries. What we can provide:
Qualified machines with CE certification.
Easier access and zero-profit spare parts support.
Timely service (any of your questions will be answered within 12 hours).
Customized equipment with all kinds of attachments.
Q: What is your delivery time?
A: We have 4 workshops, 6 production lines, and we can produce a loader in 8 minutes. Usually, as long as you contact the vessel, we can ship within 15 days.
Q: What color can I choose?
A: There are Yellow, Red, Blue, Black, White, Orange,and Green to choose. Of course you can also customize other colors you like.
Q: What kind of service can I get from you? How can I get spare parts?
A: We have 1 year warranty for each machine, within 1 year, if any parts broken because of quality issues, We professional after sales team to support you at any time.
The 5 components of an axle, their function and installation
If you're considering replacing an axle in your vehicle, you should first understand what it is. It is the component that transmits electricity from 1 part to another. Unlike a fixed steering wheel, the axles are movable. The following article will discuss the 5 components of the half shaft, their function and installation. Hopefully you were able to identify the correct axle for your vehicle. Here are some common problems you may encounter along the way.
five components
The 5 components of the shaft are flange, bearing surface, spline teeth, spline pitch and pressure angle. The higher the number of splines, the stronger the shaft. The maximum stress that the shaft can withstand increases with the number of spline teeth and spline pitch. The diameter of the shaft times the cube of the pressure angle and spline pitch determines the maximum stress the shaft can withstand. For extreme load applications, use axles made from SAE 4340 and SAE 1550 materials. In addition to these 2 criteria, spline rolling produces a finer grain structure in the material. Cutting the splines reduces the strength of the shaft by 30% and increases stress.
The asymmetric length of the shaft implies different torsional stiffness. A longer shaft, usually the driver's side, can handle more twist angles before breaking. When the long axis is intact, the short axis usually fails, but this does not always happen. Some vehicles have short axles that permanently break, causing the same failure rate for both. It would be ideal if both shafts were the same length, they would share the same load.
In addition to the spline pitch, the diameter of the shaft spline is another important factor. The small diameter of a spline is the radius at which it resists twisting. Therefore, the splines must be able to absorb shock loads and shocks while returning to their original shape. To achieve these goals, the spline pitch should be 30 teeth or less, which is standard on Chrysler 8.75-inch and GM 12-bolt axles. However, a Ford 8.8-inch axle may have 28 or 31 tooth splines.
In addition to the CV joints, the axles also include CV joints, which are located on each end of the axle. ACV joints, also known as CV joints, use a special type of bearing called a pinion. This is a nut that meshes with the side gear to ensure proper shaft alignment. If you notice a discrepancy, take your car to a shop and have it repaired immediately.
Function
Axles play several important roles in a vehicle. It transfers power from the transmission to the rear differential gearbox and the wheels. The shaft is usually made of steel with cardan joints at both ends. Shaft Shafts can be stationary or rotating. They are all creatures that can transmit electricity and loads. Here are some of their functions. Read on to learn more about axles. Some of their most important features are listed below.
The rear axle supports the weight of the vehicle and is connected to the front axle through the axle. The rear axle is suspended from the body, frame and axle housing, usually spring loaded, to cushion the vehicle. The driveshaft, also called the propshaft, is located between the rear wheels and the differential. It transfers power from the differential to the drive wheels.
The shaft is made of mild steel or alloy steel. The latter is stronger, more corrosion-resistant and suitable for special environments. Forged for large diameter shafts. The cross section of the shaft is circular. While they don't transmit torque, they do transmit bending moment. This allows the drive train to rotate. If you're looking for new axles, it's worth learning more about how they work.
The shaft consists of 3 distinct parts: the main shaft and the hub. The front axle assembly has a main shaft, while the rear axle is fully floating. Axles are usually made of chrome molybdenum steel. The alloy's chromium content helps the axle maintain its tensile strength even under extreme conditions. These parts are welded into the axle housing.
Material
The material used to make the axle depends on the purpose of the vehicle. For example, overload shafts are usually made of SAE 4340 or 1550 steel. These steels are high strength low alloy alloys that are resistant to bending and buckling. Chromium alloys, for example, are made from steel and have chromium and molybdenum added to increase their toughness and durability.
The major diameter of the shaft is measured at the tip of the spline teeth, while the minor diameter is measured at the bottom of the groove between the teeth. These 2 diameters must match, otherwise the half shaft will not work properly. It is important to understand that the brittleness of the material should not exceed what is required to withstand normal torque and twisting, otherwise it will become unstable. The material used to make the axles should be strong enough to carry the weight of a heavy truck, but must also be able to withstand torque while still being malleable.
Typically, the shaft is case hardened using an induction process. Heat is applied to the surface of the steel to form martensite and austenite. The shell-core interface transitions from compression to tension, and the peak stress level depends on the process variables used, including heating time, residence time, and hardenability of the steel. Some common materials used for axles are listed below. If you're not sure which material is best for your axle, consider the following guide.
The axle is the main component of the axle and transmits the transmission motion to the wheels. In addition, they regulate the drive between the rear hub and the differential sun gear. The axle is supported by axle bearings and guided to the path the wheels need to follow. Therefore, they require proper materials, processing techniques and thorough inspection methods to ensure lasting performance. You can start by selecting the material for the shaft.
Choosing the right alloy for the axle is critical. You will want to find an alloy with a low carbon content so it can harden to the desired level. This is an important consideration because the hardenability of the alloy is important to the durability and fatigue life of the axle. By choosing the right alloy, you will be able to minimize these problems and improve the performance of your axle. If you have no other choice, you can always choose an alloy with a higher carbon content, but it will cost you more money.
Install
The process of installing a new shaft is simple. Just loosen the axle nut and remove the set bolt. You may need to tap a few times to get a good seal. After installation, check the shaft at the points marked "A" and "D" to make sure it is in the correct position. Then, press the "F" points on the shaft flange until the points are within 0.002" of the runout.
Before attempting to install the shaft, check the bearings to make sure they are aligned. Some bearings may have backlash. To determine the amount of differential clearance, use a screwdriver or clamp lever to check. Unless it's caused by a loose differential case hub, there shouldn't be any play in the axle bearings. You may need to replace the differential case if the axles are not mounted tightly. Thread adjusters are an option for adjusting drive gear runout. Make sure the dial indicator is mounted on the lead stud and loaded so that the plunger is at right angles to the drive gear.
To install the axle, lift the vehicle with a jack or crane. The safety bracket should be installed under the frame rails. If the vehicle is on a jack, the rear axle should be in the rebound position to ensure working clearance. Label the drive shaft assemblies and reinstall them in their original positions. Once everything is back in place, use a 2-jaw puller to pry the yoke and flange off the shaft.
If you've never installed a half shaft before, be sure to read these simple steps to get it right. First, check the bearing surfaces to make sure they are clean and undamaged. Replace them if they look battered or dented. Next, remove the seal attached to the bushing hole. Make sure the shaft is installed correctly and the bearing surfaces are level. After completing the installation process, you may need to replace the bearing seals.
