Tag Archives: hand tractor

China factory Hand Front Two Discs Grass Mower Used for Walking Tractor with Best Sales

Product Description

Agricultural Machinery front Two Discs Grass Mower for walking tractor
1. Products Characters
welome to choose our grass mower The machine is light, flexible, low center of gravity, which can work normally in any direction of 30 degrees slope, mountains, hills, hedges and small areas and can be equipped with a variety of farm machineries. By removing cutter parts of the farm machinery, it is able to be installed the corresponding part on the mower to earth up, plough, rotary tillage, sow, fertilize and do transportation operations.
Our Company Advantages
Most competitive price under the service top quality, shipment on time, service in 24 hour
2.Basic Technical Data Tractor pictures
1)Disc mower for walking tractor or power tiller
2)Rotary speed:2300RPM
3)High quality

Content		Basic parameters
Operating width		≥ 80cm
Operating speed		2.0-4.0km/h
Cutting height		≥16cm
Operational efficiency		≥0.15hm2 /h
Blade speed		1800---2400r/min
Dimensions	Length	810 mm
	Wide	930 mm
	High	520 mm
Structural weight		27kg

3.The parts and Implements (related products)
We supply all kinds of spare parts for mower, welcome to send us inquiry.
4. Packing & Delivery

5.Service and Warranty
Pre-sales service
1.24 hours online, Any questions about our machine will be quickly replied.
2.Optimum design and selection according to customer's requirements and environment
3. Welcome to visit our factory and discuss cooperation
Selling service
1.test and inspect every tractor carefully and seriously
2. Technical guidance on common problems, Provide guidelines and videos on how to use them
3.send you the tractor photos for you before packing for your confirmation.

After-sales service
1. Except for fragile parts, the whole machine is guaranteed for 1 year
2. Provide 24-hour technical support via e-mail/telephone
3. We will provide you with the parts atlas and installation video.

Q1: Are you a factory or trading company?
We are a factory with self-supported import and export right.
Q2: How can I trust on your company? We are a fully registered manufacture and exporting company by China Export Registration Authorities. Moreover, our products have been exporting to a number of countries including Swi tzerland, Russia, Spain, Netherlands, Australia, Peru, Thailand,Pakistan, Indonesia, Tanzania, Nigeria, South Africa, Sudan, Congo etc. The good faith,punctual, strict quality control and reasonable price, throughout s the pledge we to each customer.
Q3: Where is your factory located? How can I visit there? Our factory is located in HangZhou City, ZheJiang Province, China. About 1 hour away from HangZhou Airport. AllI our clients are warmly welcomed to visit us!
Q4: How can I place an order from your website? It is very easy. Once you find the implement you need on our website and place an inquiry against it, or, get to the inquiry section and leave us a message there with name, country and phone number, we will get in touch with you at the earliest. You can also e-mail us directly or join us on live chat for instantaneous answers.
Q5: How can I make the payment? Payment is made via Telegraphic Transfer (T/T) through the bank against the Performa invoice. 40% as prepayment and the balance when the goods are ready for shipping.Irrevocable L/C at sight could be also accepted.
Q6: What' s the Payment terms? FOB, the price of the implement without sea shipment costs.
Q7: At which port do you usually ship the good? We usually ship goods via HangZhou, ZheJiang , HangZhou, ZheJiang port of China.
Q8. How about the Warranty ? 12 months warranty from the time of the goods arrive at destination.

                         Web:
                          HangZhou Francis  Machinery  Co., Ltd.
                        HangZhou City,ZheJiang Province, China

How to Replace a Bearing

If you want to select a bearing for a specific application, you should know a few basics. This article will give you an overview of ball, angular contact, and sliding-contact bearings. You can choose a bearing according to the application based on the characteristics of its material and preload. If you are not sure how to choose a bearing, try experimenting with it. The next step is to understand the Z-axis, which is the axes along which the bearing moves.

Z axis

When it comes to replacing your Z axis bearing, there are several things you must know. First, you need to make sure that the bearings are seated correctly. Then, you should check the tension and rotation of each one. To ensure that both bearings are equally tensioned, you should flex the Core to the desired angle. This will keep the Z axis perpendicular to the work surface. To do this, first remove the Z axis bearing from its housing and insert it into the Z axis motor plate. Next, insert the flanged bearing into the Z axis motor plate and secure it with 2 M5x8mm button head cap screws.
Make sure that the bearing plate and the Z Coupler part are flush and have equal spacing. The spacing between the 2 parts is important, as too much spacing will cause the leadscrew to become tight. The screws should be very loose, with the exception of the ones that engage the nylocks. After installing the bearing, the next step is to start the Z axis. Once this is done, you'll be able to move it around with a stepper.

Angular contact

bearing
Ball bearings are made with angular contacts that result in an angle between the bearing's races. While the axial load moves in 1 direction through the bearing, the radial load follows a curved path, tending to separate the races axially. In order to minimize this frictional effect, angular contact bearings are designed with the same contact angle on the inner and outer races. The contact angle must be chosen to match the relative proportions of the axial and radial loads. Generally, a larger contact angle supports a higher axial load, while reducing radial load.
Ball bearings are the most common type of angular contact bearings. Angular contact ball bearings are used in many applications, but their primary purpose is in the spindle of a machine tool. These bearings are suitable for high-speed, precision rotation. Their radial load capacity is proportional to the angular contact angle, so larger contact angles tend to enlarge with speed. Angular contact ball bearings are available in single and double-row configurations.
Angular contact ball bearings are a great choice for applications that involve axial loads and complex shapes. These bearings have raceways on the inner and outer rings and mutual displacement along the axial axis. Their axial load bearing capacity increases as the contact Angle a rises. Angular contact ball bearings can withstand loads up to 5 times their initial weight! For those who are new to bearings, there are many resources online dedicated to the subject.
Despite their complexity, angular contact ball bearings are highly versatile and can be used in a wide range of applications. Their angular contact enables them to withstand moderate radial and thrust loads. Unlike some other bearings, angular contact ball bearings can be positioned in tandem to reduce friction. They also feature a preload mechanism that removes excess play while the bearing is in use.
Angular contact ball bearings are made with different lubricants and cage materials. Standard cages for angular contact ball bearings correspond to Table 1. Some are machined synthetic resins while others are molded polyamide. These cage materials are used to further enhance the bearing's axial load capacity. Further, angular contact ball bearings can withstand high speeds and radial loads. Compared to radial contact ball bearings, angular contact ball bearings offer the greatest flexibility.

Ball bearings

bearing
Ball bearings are circular structures with 2 separate rings. The smaller ring is mounted on a shaft. The inner ring has a groove on the outer diameter that acts as a path for the balls. Both the inner and outer ring surfaces are finished with very high precision and tolerance. The outer ring is the circular structure with the rolling elements. These elements can take many forms. The inner and outer races are generally made of steel or ceramic.
Silicon nitride ceramic balls have good corrosion resistance and lightweight, but are more expensive than aluminum oxide balls. They also exhibit an insulating effect and are self-lubricating. Silicon nitride is also suitable for high-temperature environments. However, this type of material has the disadvantage of wearing out rapidly and is prone to cracking and shattering, as is the case with bearing steel and glass. It's also less resistant to heat than aluminum oxide, so it's best to buy aluminum nitride or ceramic ball bearings for applications that are subjected to extremely high temperatures.
Another type of ball bearings is the thrust bearing. It has a special design that accommodates forces in both axial and radial directions. It is also called a bidirectional bearing because its races are side-by-side. Axial ball bearings use a side-by-side design, and axial balls are used when the loads are transmitted through the wheel. However, they have poor axial support and are prone to separating during heavy radial loads.
The basic idea behind ball bearings is to reduce friction. By reducing friction, you'll be able to transfer more energy, have less erosion, and improve the life of your machine. With today's advances in technology, ball bearings can perform better than ever before. From iron to steel to plastics, the materials used in bearings have improved dramatically. Bearings may also incorporate an electromagnetic field. So, it's best to select the right 1 for your machine.
The life expectancy of ball bearings depends on many factors, including the operating speed, lubrication, and temperature. A single million-rpm ball bearing can handle between 1 and 5 million rotations. As long as its surface contact area is as small as possible, it's likely to be serviceable for at least 1 million rotations. However, the average lifespan of ball bearings depends on the application and operating conditions. Fortunately, most bearings can handle a million or more rotations before they start showing signs of fatigue.

Sliding-contact bearings

bearing
The basic principle behind sliding-contact bearings is that 2 surfaces move in contact with 1 another. This type of bearing works best in situations where the surfaces are made of dissimilar materials. For instance, a steel shaft shouldn't run in a bronze-lined bore, or vice versa. Instead, 1 element should be harder than the other, since wear would concentrate in that area. In addition, abrasive particles tend to force themselves into the softer surface, causing a groove to wear in that part.
Sliding-contact bearings have low coefficients of friction and are commonly used in low-speed applications. Unlike ball and roller bearings, sliding contact bearings have to be lubricated on both sides of the contacting surfaces to minimize wear and tear. Sliding-contact bearings generally are made of ceramics, brass, and polymers. Because of their lower friction, they are less accurate than rolling-element bearings.
Sliding-contact bearings are also known as plain or sleeve bearings. They have a sliding motion between their 2 surfaces, which is reduced by lubrication. This type of bearing is often used in rotary applications and as guide mechanisms. In addition to providing sliding action, sliding-contact bearings are self-lubricating and have high load-carrying capacities. They are typically available in 2 different types: plain bearings and thrust bearings.
Sliding-contact linear bearing systems consist of a moving structure (called the carriage or slide) and the surfaces on which the 2 elements slide. The surfaces on which the bearing and journal move are called rails, ways, or guides. A bore hole is a complex geometry, and a minimum oil film thickness h0 is usually used at the line of centers. It is possible to have a sliding-contact bearing in a pillow block.
Because these bearings are porous, they can absorb 15 to 30% of the lubrication oil. This material is commonly used in automobile and machine tools. Many non-metallic materials are used as bearings. One example is rubber, which offers excellent shock absorbency and embeddability. While rubber has poor strength and thermal conductivity, it is commonly used in deep-well pumps and centrifugal pumps. This material has high impact strength, but is not as rigid as steel.

China factory Hand Front Two Discs Grass Mower Used for Walking Tractor with Best Sales

China Professional Spare Parts of 10HP Small Rotary Power Weeder Tiller Hand Tractor Tiller Cultivator with Great quality

Product Description

PRODUCT SPECIFICATION
Product Name	Farm Agriculture Hand Power Tiller
Brand	HangZhou
Model	Gasoline 177
Power Type	Gasoline
Machine Type	Cultivator
Weight	120KG
Dimension(LWH)	1500600950mm
Power	10HP
Engine type	Gasoline Engine
Transfer method	Belt drive, Full gear One-piece box
Oil volume	3.5L-4.0L
Handhold	Adjustable up and down, 360 degree left and right rotation
Gear	Tool box (high speed, neutral, low speed), traveling box (fast, neutral, low speed), whole machine (forward, neutral, reverse)
Ditch	Width 12cm-60cm, Depth 10cm-70cm (Depth can be adjusted freely and limited depth wheel)
Earth up	Height 40cm. Crop row spacing between 45cm-120cm
Rotary tillage	Width 75cm, depth 7cm-20cm
Track width	The total width of walking iron wheel is 12cm-20cm-26cm. Rubber wheel width 48cm The total width of the roller is 85cm

Our Advantages

1.Better small machine could be guarantee the farm worker in some time.

2.Its advantage is fit for old man,woman to finish tilling fields.

3.Special diesel engine must need special transmission to match each other.so the gearbox of tiller is our patent solely.

4.Features: Compact,Agile,Light,Reliable,Convenience,High Quality.

5.Suitable for paddy fields,upland plains,mountain and hilly areas.and for plough,rotary tillage,sow,threshing ,suction and so on.

6.Equipped with lightnings for driving at night.

7.With quick coupling,easy to change farming implements. Cultivator,mower,trailer,water pump,power tiller,snow blower,rotary plough,etc.

Packaging & Shipping

Company Profile

ZheJiang HangZhou Agricultural Equipment Co., Ltd specializes in the production of agricultural equipment such as pastoral management machine, ditching and soil cultivating machine, cultivator, ditching and ridging machine, pastoral management machine, micro tillage machine and so on. These machines can be used for orchard cultivation, special purpose for greenhouses, trenching and soil cultivation of various cash crops such as green onions, ginger, potatoes, strawberries and sugarcane.

Founded in 2012, the company covers an area of 20000 square meters and a plant area of 10000 square meters. Main products: CZPT accessories, foreign trade export, agricultural equipment. The company has complete equipment, advanced robot welding, laser cutting and processing center, strong technical force and perfect testing means, and has passed ISO9001. TS16949 quality management system certification.

We can provide high-quality products for users all over the country in the shortest time. Our products are sold to major domestic markets, and our company adheres to the principle of "quality, user first, people-oriented and service for the people" in North America, Europe, South America, Southeast Asia, the Middle East and Africa, so as to ensure to provide users with timely, thoughtful, high-quality and satisfactory after-sales service.

After Sales Service

Before-sale services:
1) 24 Hours online service, quickly reply for E-mail and online ask. Xihu (West Lake) Dis. customers to choose the best applicable machine type.
2) Professionally and patiently introduction, provide the advanced, energy-saving and practical technological process.

Sale services:
1) complete parts safety stock for all machine series. Test every machine before delivery to insure good performance of machine.
2) In accordance with the agreements stipulated in the contract

After-sale services:
1) According to the special requirements of customers,our company can ask professional engineers to CZPT with device installation online, debugging and training operators until customers are fully satisfied.
2) The quality guarantee period for machines is 1 year except the wearing parts and human damage factor.

FAQ

1.Q:Are you manufacturer or trade company?
A: We are manufacturer, we have our own factory. Our factory has department for exploitation , producing, sales, after-sell service, packing , warehouse, we can offer you best products and best service.

2. Q: Do you sell accessories for your machine?
A: Yes, all of matching accessories for our machine are on selling, we are willing to supply the matching parts to you with low price.

3.Q: What's your terms of packing?
A: Generally, we pack our goods in wooden cases.

4.Q: What's your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages before you pay the balance.

5.Q: What's your terms of delivery?
A: EXW, FOB, CFR, CIF

6.Q: How about delivery time?
A: Generally, it will take 30 to 40 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

7.Q: How do you make our business long-term and good relationship?
A: 1. We keep good quality and competitive price to ensure our customers benefit;
2. We respect every customer as our friend, no matter where they come from;
3. If you have any feedback that is cherished to us, please send email to us.

What is a driveshaft and how much does it cost to replace one?

Your vehicle is made up of many moving parts. Knowing each part is important because a damaged driveshaft can seriously damage other parts of the car. You may not know how important your driveshaft is, but it's important to know if you want to fix your car. In this article, we'll discuss what a driveshaft is, what its symptoms are, and how much it costs to replace a driveshaft.
air-compressor

Repair damaged driveshafts

A damaged driveshaft does not allow you to turn the wheels freely. It also exposes your vehicle to higher repair costs due to damaged driveshafts. If the drive shaft breaks while the car is in motion, it may cause a crash. Also, it can significantly affect the performance of the car. If you don't fix the problem right away, you could risk more expensive repairs. If you suspect that the drive shaft is damaged, do the following.
First, make sure the drive shaft is protected from dust, moisture, and dust. A proper driveshaft cover will prevent grease from accumulating in the driveshaft, reducing the chance of further damage. The grease will also cushion the metal-to-metal contact in the constant velocity joints. For example, hitting a soft material is better than hitting a metal wall. A damaged prop shaft can not only cause difficult cornering, but it can also cause the vehicle to vibrate, which can further damage the rest of the drivetrain.
If the driveshaft is damaged, you can choose to fix it yourself or take it to a mechanic. Typically, driveshaft repairs cost around $200 to $300. Parts and labor may vary based on your vehicle type and type of repair. These parts can cost up to $600. However, if you don't have a mechanical background, it's better to leave it to a professional.
If you notice that 1 of the 2 drive shafts is worn, it's time to repair it. Worn bushings and bearings can cause the drive shaft to vibrate unnecessarily, causing it to break and cause further damage. You can also check the center bearing if there is any play in the bearing. If these symptoms occur, it is best to take your car to a mechanic as soon as possible.
air-compressor

Learn about U-joints

While most vehicles have at least 1 type of U-joint, there are other types available. CV joints (also known as hot rod joints) are used in a variety of applications. The minor axis is shorter than the major axis on which the U-joint is located. In both cases, the U-joints are lubricated at the factory. During servicing, the drive shaft slip joint should be lubricated.
There are 2 main styles of U-joints, including forged and press fit. They are usually held in place by C-clamps. Some of these U-joints have knurls or grooves. When selecting the correct fitting, be sure to measure the entire fitting. To make sure you get the correct size, you can use the size chart or check the manual for your specific model.
In addition to lubrication, the condition of the U-joint should be checked regularly. Lubricate them regularly to avoid premature failure. If you hear a clicking sound when shifting gears, the u-joint space may be misaligned. In this case, the bearing may need to be serviced. If there is insufficient grease in the bearings, the universal joint may need to be replaced.
U-joint is an important part of the automobile transmission shaft. Without them, your car would have no wheeled suspension. Without them, your vehicle will have a rickety front end and a wobbly rear end. Because cars can't drive on ultra-flat surfaces, they need flexible driveshafts. The U-joint compensates for this by allowing it to move up and down with the suspension.
A proper inspection will determine if your u-joints are loose or worn. It should be easy to pull them out. Make sure not to pull them all the way out. Also, the bearing caps should not move. Any signs of roughness or wear would indicate a need for a new UJ. Also, it is important to note that worn UJs cannot be repaired.

Symptoms of Driveshaft Failure

One of the most common problems associated with a faulty driveshaft is difficulty turning the wheels. This severely limits your overall control over the vehicle. Fortunately, there are several symptoms that could indicate that your driveshaft is failing. You should take immediate steps to determine the cause of the problem. One of the most common causes of driveshaft failure is a weak or faulty reverse gear. Other common causes of driveshaft damage include driving too hard, getting stuck in reverse gear and differential lock.
Another sign of a failed driveshaft is unusual noise while driving. These noises are usually the result of wear on the bushings and bearings that support the drive shaft. They can also cause your car to screech or scratch when switching from drive to idle. Depending on the speed, the noise may be accompanied by vibration. When this happens, it's time to send your vehicle in for a driveshaft replacement.
One of the most common symptoms of driveshaft failure is noticeable jitter when accelerating. This could be a sign of a loose U-joint or worn center bearing. You should thoroughly inspect your car to determine the cause of these sounds and corresponding symptoms. A certified mechanic can help you determine the cause of the noise. A damaged propshaft can severely limit the drivability of the vehicle.
Regular inspection of the drive shaft can prevent serious damage. Depending on the damage, you can replace the driveshaft for anywhere from $500 to $1,000. Depending on the severity of the damage and the level of repair, the cost will depend on the number of parts that need to be replaced. Do not drive with a bad driveshaft as it can cause a serious crash. There are several ways to avoid this problem entirely.
The first symptom to look for is a worn U-joint. If the U-joint comes loose or moves too much when trying to turn the steering wheel, the driveshaft is faulty. If you see visible rust on the bearing cap seals, you can take your car to a mechanic for a thorough inspection. A worn u-joint can also indicate a problem with the transmission.
air-compressor

The cost of replacing the drive shaft

Depending on your state and service center, a driveshaft repair can cost as little as $300 or as high as $2,000, depending on the specifics of your car. Labor costs are usually around $70. Prices for the parts themselves range from $400 to $600. Labor costs also vary by model and vehicle make. Ultimately, the decision to repair or replace the driveshaft will depend on whether you need a quick car repair or a full car repair.
Some cars have 2 separate driveshafts. One goes to the front and the other goes to the back. If your car has 4 wheel drive, you will have two. If you're replacing the axles of an all-wheel-drive car, you'll need a special part for each axle. Choosing the wrong 1 can result in more expensive repairs. Before you start shopping, you should know exactly how much it will cost.
Depending on the type of vehicle you own, a driveshaft replacement will cost between PS250 and PS500. Luxury cars can cost as much as PS400. However, for safety and the overall performance of the car, replacing the driveshaft may be a necessary repair. The cost of replacing a driveshaft depends on how long your car has been on the road and how much wear and tear it has experienced. There are some symptoms that indicate a faulty drive shaft and you should take immediate action.
Repairs can be expensive, so it's best to hire a mechanic with experience in the field. You'll be spending hundreds of dollars a month, but you'll have peace of mind knowing the job will be done right. Remember that you may want to ask a friend or family member to help you. Depending on the make and model of your car, replacing the driveshaft is more expensive than replacing the parts and doing it yourself.
If you suspect that your drive shaft is damaged, be sure to fix it as soon as possible. It is not advisable to drive a car with abnormal vibration and sound for a long time. Fortunately, there are some quick ways to fix the problem and avoid costly repairs later. If you've noticed the symptoms above, it's worth getting the job done. There are many signs that your driveshaft may need service, including lack of power or difficulty moving the vehicle.

China Professional Spare Parts of 10HP Small Rotary Power Weeder Tiller Hand Tractor Tiller Cultivator with Great quality

China Custom 70HP Yto/Foton Lovol/John Deere/New Holland/Dongfeng/Four Wheel Compact Agriculture Hand Traktor Mini Small Farm Walking Agricultural Electric Tractor 50HP with high quality

Product Description

70HP YTO/Foton Lovol/John Deere/New holland/Xihu (West Lake) Dis.feng/Four Wheel Compact Agriculture Hand Traktor Mini Small Farm Walking Agricultural Electric Tractor 50HP

This series tractor is 4wd model and with reasonable structure. Our company research and develop the new type special gearbox and rear axle, with the synchronizer shifts + shuttle shifts, bolder half shaft, stronger gears and reinforced brake assembly.

Sales Territory: Regions like Europe, South America and Australia, Africa and other areas
Matched Machines and Tools: Ploughing tools like disc plough, disc harrow, rotary tiller and cultivator. Optional tools like front loader, backhoe, trailer, mower, rake, spraying machine.

LIFTOR Tractor Features:

1. For the front axle, the tractor use special high power electric hydraulic differential lock.

2. The hydraulic steering, make the operation much more flexible, and much more suitable for any different working environment Weichai-Deutz engine, and the special 16 inch double clutch, make the tractor much more powerful;

3. The electric hydraulic clutch, independent driving and braking system, make the operation much convenient and labor-saving Double speed power output(PTO), multi-way hydraulic output, and unlimited adjustable rear wheel tread, suit for a variety of agricultural farm implements requirements.

4. The tractor can be equipped with new special luxury air-conditioned cabin, which is safe, comfortable and convenient on maintenance.

Tractor Parameter:

TG series tractor(180hp-220hp)
Product model	HX1804(180hp)	HX2104(210hp)	HX2204(220hp)
Wheel drive	4×4
Dimension(LWH)	5400×2460×3140mm
Weight	8000kg
Front wheel tread	1990mm
Rear wheel tread	1840(1820-1910)mm
Wheel base	2890mm
Min land clearence	430mm
Gear shifts	16F+16R
Tire size	16.9-28/20.8-38
Steering gear	Hydraulic steering
Rear Suspension	Three point suspension
ENGINE SPECIFICATION
Engine model	Weichai
Engine type	Water cooled, vertical, 4 stroke and direct injection
Rated power(kw)	132.3	154.4	161.7
Rated revolution	2300/2400 r/min
start way	Electric start
Transmission	4×4×(1+1) shifts
Clutch	Dry friction, double stage clutch, seperate operation
PTO speed	6 splined 540/1000

LIFTOR Tractor Pictures:

Optional Implements for Tractor :

About US:

"Liftor Enterprises" is a high-tech enterprise professionally specialized in R&D, production, sales, service of electric storage,intelligent industrial system, agriculatural tractor, lifting machine and wheel loader. It is located in HangZhou, ZheJiang Province with advanced forklift manufacturer technology, processing equipment and perfect product testing center.

Our company is the China Automobile Industry Association member unit. We won the honorary title such as "Outstanding Enterprise of Quality Management, Credibility and Service AAA level", "National Enterprise of Good Creditworthiness", "National Quality Management Advanced Enterprise" etc. The company has already passed the safety production standardization and the quality authentication of ISO9001:2008 and European Union CE certification, fit-out national patent certificate.

Our main equipment are agriculatural tractor, lifting machine, wheel loader and forklift. It is widely used in various places of modern logistics.

FAQ:

1. Manufacturer or Trading Company?
We are leading tractor manufacturer for 20 years, and specialize in 12-240Hp tractors in China.

2. MOQ: Mini tractor: 8 units; Middle tractor(25-40hp): 2 units; Above 50hp: 1 unit

3. Spare Parts: Free toolbox and easy damaged parts.

4. Shippment: We can help you arrange shippment.

5. Delivery Time: Usually 25 days. In CZPT season,30-40 days

6. Warranty Time: Complete service system, 12 months since arrival of destination port

7. Payment Terms: We accept 30%T/T in advance, and 70% T/T before delivery

8. Tractor Options: Can be equipped with ROPS, Canopy, Cabin, AC Cabin, Air Brakes, Hydraulic Valve Out, Paddy Tire or as per your requirements.

9. Tractor Logo: We have our own logo. And we also can put your logo for free.

10. Package and Loading: (1).complete tractor package: 2 units/20GP, 4 units/40HQ;(2).Iron Frame Package: 8 units/20GP, 16 units/40HQ

11. Tractor Implements: Rotary tiller, disc plow, furrow plow, cultivator, front end Loader, backhoe, Mower, Trailer, Snow Blower or as per your requirements.

12. Part supply: Complete Parts Workshop, and can supply all parts

Axle Spindle Types and Features

The axle spindle is an integral part of your vehicle's suspension. There are several different types and features, including mounting methods, bearings, and functions. Read on for some basic information on axle spindles. The next part of the article will cover how to choose the correct axle spindle for your vehicle. This article will also discuss the different types of spindles available, including the differences between the rear and front bearings.
Driveshaft

Features

The improved axle spindle nut assembly is capable of providing additional performance benefits, including increased tire life and reduced seal failure. Its keyway features and radially inwardly extending teeth allow nut adjustment to be accomplished with precision. The invention further provides a unique, multi-piece locking mechanism that minimizes leakage and torque transfer. Its principles and features are detailed in the appended claims. For example, the improved axle spindle nut assembly is designed for use in vehicles that are equipped with a steering system.
The axle spindle nut assembly includes a nut 252 with threads 256 on its inner periphery. The axle spindle 50 also features threads 198 on its outer periphery. The nut is threaded onto the outboard end of the axle spindle 50 until it contacts the inboard surface of the axle spacer 26. In the assembled state, a bearing spacer 58 is also present on the axle spindle.
The axle spindle nut assembly can reduce axial end play between the wheel end assembly 52 and the axle spindle 50. It can be tightened to an extreme torque level, but if the thread faces separate, it will undercompress the bearing cone and spacer group. To minimize these disadvantages, the axle spindle nut assembly is a critical component of a wheel-end assembly. There are several types of axle spindle nuts.
The third embodiment of the axle spindle nut assembly 300 comprises an inner washer 202, an outer washer 310, and at least 1 screw 320. The axle spindle nut assembly 300 secures and preloads bearing cones 55, 57. Unlike the first embodiment, the axle spindle nut assembly 300 uses the inner washer 202, which is optional in the third embodiment. The inner washer 202 and outer washer 310 are similar to those of the first embodiment.

Functions

An axle spindle is 1 of the most important components of a vehicle's suspension system. The spindle retains the position of bearings and a spacer in an axle by providing clamp force. The inner nut of an axle spindle should be properly torqued to ensure a secure fit. A spindle nut is also responsible for compressing bearings and spacers. If any of these components are missing, the spindle will not work properly.
An axle spindle is used in rear wheel drive cars. It carries the weight of the vehicle on the axle casing and transfers the torque from the differential to the wheels. The axle spindle and hub are secured on the spindle by large nuts. The axle spindle is a vital component of rear wheel drive vehicles. Hence, it is essential to understand the functions of axle spindle. These components are responsible for the smooth operation of a vehicle's suspension system.
Axle spindles can be mounted in 3 ways: in the typical axle assembly, the spindles are bolted onto the ends of the tubular axle, and the axle is suspended by springs. Short stub-axle mounting uses a torsion beam that flexes to provide a smooth ride. A second washer is used to prevent excessive rotation of the axle spindle.
Apart from being a crucial component of the suspension system, the spindles of the wheels are responsible for guiding the vehicle in a straight line. They are connected to the steering axis and are used in different types of suspension systems. European cars use a MacPherson Strut suspension system in which the spindle is connected to the arms in the front and rear of the suspension frame. The MacPherson strut allows the shock absorber housing to turn the wheel.
Driveshaft

Methods of mounting

Various methods of mounting axle spindle are available. In general, these methods involve forming a tubular blank of uniform cross section and thickness, and receiving the bearing assembly against it. The spindle is then secured using a collar, which also serves as a bearing stop. In some cases, additional features are used to provide greater security. Some of these features may not be suitable for all applications. But they are generally suitable.
Axle spindle forming is usually done by progressive steps using hollow punches. The metallic body of the punch has an inner work surface, which receives the axle blank. A mandrel is fixed within the work opening of the punch. The punch body's work surface forges the spindle about the mandrel. The punch has 2 ends, a closed and an open one.
A wheeled vehicle axle assembly (10) includes a cylindrical housing member (12 a) and a plurality of spindle mounting flanges (30) secured on the housing member. The spindles (16) are firmly attached to the housing member by means of coupling members. The coupling members are configured to distribute the bending loads imposed on the spindle by the axle. It is important to note that the coupling members can be either threaded or screwed.
Traditionally, axle spindles were made from tubular blanks of irregular thickness. This method allowed for a gradual reduction in diameter and eliminated the need for extra metal within the spindle. Similarly, axles made by cold forming eliminate the need for additional metal in the spindle. In this way, the overall cost of manufacture is also reduced. The material used for manufacturing axles also determines the size and shape of the final product.
Driveshaft

Bearings

A nut 16 is used to retain the wheel bearings on axle spindle 12. The nut comprises several parts. The first portion includes a plurality of threads and a deformable second portion. The nut may be disposed on the inboard or outboard end of the axle spindle. This type of nut is typically secured to the axle spindle by a retaining nut.
The bearings are installed in the spindle to allow the wheel hub to rotate. While bearings are greased, they can dry out over time. Consequently, you may hear a loud clicking sound when turning your vehicle. Alternatively, you may notice grease on the edges of your tires. Bearing failure can cause severe damage to your axle spindle. If you notice any of these symptoms, you may need to replace the bearings on your axle spindle. Fortunately, you can purchase the necessary bearing parts at O'Reilly Auto Parts.
There are 3 ways to mount an axle spindle. A typical axle assembly has the spindles bolted to the ends of the tubular axle. A torsion beam is also used to mount the spindles on the axle. This torsion beam acts like a spring to help make the ride smooth and bump-free. Lastly, the axle spindle is sometimes mounted as a bolt-on component.

Cost

If your axle spindle has been damaged, you may need to have it replaced. This part of the axle is relatively easy to replace, but you need to know how to do it correctly. To replace your axle spindle, you must first remove the damaged one. To do this, a technician will cut the weld. They will then thread the new 1 into the axle tube and torque it to specification. After that, they will weld the new axle spindle into place.
When you are thinking about the cost of an axle spindle replacement, you must first determine if it is worth it for your vehicle. It is generally a good idea to replace the spindle only if it is causing damage to your vehicle. You can also replace your axle housing if it is deteriorating. If you do not replace the spindle, you can risk damaging the axle housing. To save money, you can consider using a repair kit.
You can also purchase an axle nut socket set. Most wrenches have an adjusting socket for this purpose. The socket set should be suitable for most vehicle types. Axle spindle replacement costs around $500 to $600 before tax. However, you should be aware that these costs vary widely based on the type of vehicle you have. The parts can cost between $430 and $480, and the labor can cost anywhere from $50 to 70.

China Custom 70HP Yto/Foton Lovol/John Deere/New Holland/Dongfeng/Four Wheel Compact Agriculture Hand Traktor Mini Small Farm Walking Agricultural Electric Tractor 50HP with high quality

China Professional Liftor/Foton/Yto/Kubata 20/60HP 604 Hand Rotary Electric Power Tiller Price Compact Mini Small Tractor Farm Walking Garden Agricultural Machinery Tractor with Free Design Custom

Product Description

LIFTOR/Foton/YTO/Kubata 60HP 604 Hand Rotary Electric Power Tiller Price Compact Mini Small Tractor Farm Walking Garden Tractor Agricultural Machinery

NBS chassis tractor is a group tractor for general purpose. It can be used in plain, hill, mountain area,
paddy field, orchard, grassland and meadow.It can accomplish various farm tools such as plow, harrow,
planter, harvester and trailer,etc. Following is TY chassis tractor details, please check.

LIFTOR Tractor Features:

1. CZPT series tractor is designed for multiple light works, such as farming, transportation etc.

2. Equipped with Chinese famous diesel engine, It has the advantage of high cost efficiency and fuel efficiency, low maintenance cost and good working performance.

3. Using central console and mature structure, the tractor is easy to control and maintain.

4. 8F+2R gearbox with easy operation and convenient maintenance;

5. Optional single/double action clutches for different needs and operation;

6. Optional Herringbone tires, paddy tires or other type of tires to meet your needs of working conditions.

7. Hydraulic power steering(4WD) makes it easy to control and reduce the labor strength of operator.

Tractor Parameter:

Model	HX504	HX604
Wheel Drive	4x4	4x4
Horse Power	50 HP	60 HP
Chassis Model	Small HangZhou Chassis
Tractor With Roll Bar and Roof Dimension(LxWxH)	3550x1650x2360 mm
Tractor With Warm Wind Cabin Dimension(LxWxH)	3550x1650x2460 mm
Minimum Service Quality	1860 kgs	1940kgs
Front Wheel Tread	1300 mm
Rear Wheel Tread	1300 mm
Wheel Base	1850 mm
Minimum Ground Clearance	365 mm
Gear Shifts	8F + 2R
Tire Size	6.5-16/11.2-24 Inch
Engine Specification
Engine Brand	Quanchai	Xinchai
Emission Standard	3
Engine Model	4B5-50V32	4D27ZT32
Type	Water Cooled Four Cylinders In-line Engine
Rated Power	36.8kw	44.2kw
Rated Revolution	2400 r/min
Start Way	Electric Start
Gear Box	(4+1)x2
Clutch	Single Action
PTO Speed	Double Speed, 6 Splines